The Gen IV is Vintage Air's most powerful and intelligent climate control system. The Gen IV uses an exclusive fully electronic microprocessor control system that eliminates cables or vacuum connections. Separate high-capacity copper parallel-flow heat coil and aluminum plate-and fin-cooling coils provide outstanding performance and instant temperature adjustments.
Additional features include variable blower speed and dash/floor/defrost blend.
**Evaporator kit includes the evaporator unit and mounting brackets louvers (where required) duct hose wiring harness new control panel hardware and installation instructions.
This Evaporator kit can be utilized for all Regal trims. The new electronic control panel will fit all Regal trims as well and is included in the Evaporator kit.
• There are twithout options for the Condenser Kit (Turbo and Non-Turbo). If your compressor is mounted on the driver’s side of the vehicle use the Turbo Condenser kit. If the compressor is located on the Passenger’s side of the vehicle use the Non-Turbo Condenser kit option.
• There are twithout Hose kit options the Standard hose kit and the Modified hose kit. The Standard hose kit will only fit 1986-87 Grand National and T-type. The hose lengths and fittings are specific for these years and trim. For other trims use the Modified hose kit which will allow the A/C hoses to be cut to length and fittings to be clocked to your needs.
• At this time there is only one compressor bracket kit available for the Buick Regal which is designed to only fit the 1986-87 Grand National and T-type. This bracket kit was designed using a 7B10 compressor. This compact compressor was used due to the tight clearance in the engine bay.
Bullet Points
Fly-By-Wire fully electronic servo motor controls with no cables or capillary tube to route
Infinite just-right-temperature air blending
Infinite blower fan speed adjustment
High-volume dehumidified defrost mode
Separate high-capacity aluminum plate & fin cooling coil
High-Capacity parallel-flow heater core
Mounts behind the dash
Includes new bolt-in, LED backlit control panel
Stamped steel firewall cover panel
Steel firewall water drip tray
Replacement steel glove box (reduced capacity)
Additional features include variable blower speed and dash/floor/defrost blend.
**Evaporator kit includes the evaporator unit and mounting brackets louvers (where required) duct hose wiring harness new control panel hardware and installation instructions.
This Evaporator kit can be utilized for all Regal trims. The new electronic control panel will fit all Regal trims as well and is included in the Evaporator kit.
• There are twithout options for the Condenser Kit (Turbo and Non-Turbo). If your compressor is mounted on the driver’s side of the vehicle use the Turbo Condenser kit. If the compressor is located on the Passenger’s side of the vehicle use the Non-Turbo Condenser kit option.
• There are twithout Hose kit options the Standard hose kit and the Modified hose kit. The Standard hose kit will only fit 1986-87 Grand National and T-type. The hose lengths and fittings are specific for these years and trim. For other trims use the Modified hose kit which will allow the A/C hoses to be cut to length and fittings to be clocked to your needs.
• At this time there is only one compressor bracket kit available for the Buick Regal which is designed to only fit the 1986-87 Grand National and T-type. This bracket kit was designed using a 7B10 compressor. This compact compressor was used due to the tight clearance in the engine bay.
Bullet Points
Fly-By-Wire fully electronic servo motor controls with no cables or capillary tube to route
Infinite just-right-temperature air blending
Infinite blower fan speed adjustment
High-volume dehumidified defrost mode
Separate high-capacity aluminum plate & fin cooling coil
High-Capacity parallel-flow heater core
Mounts behind the dash
Includes new bolt-in, LED backlit control panel
Stamped steel firewall cover panel
Steel firewall water drip tray
Replacement steel glove box (reduced capacity)
